Description

The POPE Professional® MA-7200 is 2U and MA-8200 is 3U, high performance power amplifier designed to meet the most stringent needs of  professional use in concert touring, high quality sound reinforcement and professional fixed installations. This amplifier is fully comparable with the other Professional Series amplifiers.

 

 

 

Features

•    Enhanced protection
•    Precise power amp output
•    4 forced air cooling fans system
•    2mm thick "In-One" rugged steel chassis - durable, strong, and easy for maintenance
•    Advanced power supply technology
•    Class H architecture
•    Automatic gain control (AGC) circuit, decrease distortion
•    2-channel Stereo, bridge mono or parallel connection

Application

The MA Series Amplifiers can use stadium, dance hall, concerts and touring live performances. 

Power Output

Ratings (RMS @ 1% THD @ 230VAC

Model MA-7200 MA-8200
Number of channels 2 2
Total output all channels driven 3000 W @ 4 ohm 4600 W @ 4 ohms
Max. Output Power 4 ohms 8 ohms 4 ohms 8 ohms
Per channel watts 1500 W 950 W 2300 W 1500 W
Bridge Mono 3000 W 1900 W 4600 W 3000W

Specification

Frequency Response ±0.1 dB from 20 Hz to 20 kHz at 1 watt
Phase Response ±10 degrees from 10 Hz to 20 kHz at 1 watt
THD 0.05%
Intermodulation Distortion
(IMD)
<0.35% (60 Hz and 7 kHz at 4:1, from full rated output to -30dB)
Signal-to-Noise Ratio >105 dB A-weighted or 100 dB unweighted below rated power, 20 Hz - 20 kHz.
CMRR (20 Hz to 1 kHz) > 55 dB, typically > 70 dB
Crosstalk (below rated
power, 20 Hz to 1 kHz)
> 80 dB
Slew Rate 80V/usec
Damping Factor  >2,000 from 10 Hz to 400 Hz
Input Impedance (Nominal) 20KΩ Balanced
Signal Input Two balanced 3-pin female XLR connectors
Signal Output Parallel two balanced 3-pin male XLR connectors
Input Sensitivity gain 0.775 / 1 / 1.44 Volt
Output Circuitry Class H
Output Connector Two sets of Red & Black color coded binding posts & two Neutrik® Speakon® 4 pole chassis connector
Connectors Neutrik® 3-pin XLR, Neutrik® Speakon® 4 pole chassis connector
LED Indicator Power, Signal, Protect, Clip
Protection Protected against shorted, open or mismatched loads, overloaded power supplies, excessive temperature, chain destruction phenomena, input overload damage and high-frequency blowups. Also protect loudspeakers from input/output DC and turn-on/turn-off transients
Cooling System Internal heat sinks fitted with four variable speed fans for uniform heat dissipation from rear to front air flow
Construction Steel chassis with durable black powder coat finish
Power Supply Toroidal Transformer
Power Range 200 - 240V AC @ 50Hz
Model MA-7200 MA-8200
Input Watts
(Power Consumption)
1600W 1900W
Dimension (W x D x H)
482mm × 443.5mm × 88.8mm
482mm × 468mm×132mm
Size
2U
3U
Weight (Kg)
26.2 Kg (57.7 lbs)
36.0 Kg (79.3 lbs)

Description

The POPE Professional® MAC Series of Amplifiers are specially designed for touring and installation. It's unique design and powerful output can meet the requirement of any sound reinforcement project.

 

 

 

Features

  • CLASS H circuit to improve the power amplifier's efficiency, stability & decrease the temperature in operation.
  • Perfect protection,e.g. short-circuit protection, overtemperature protection and DC protection.
  • The fan with variable speed for cooling.
  • Built-in compression function to prevent the power amplifier from distortion of over input.

Application

The MAC Series Amplifiers can use stadium, dance hall, concerts and touring live performances.

Power Output

Ratings (RMS @ 1% THD @ 230VAC

Model MAC-2202 MAC-3202 MAC-5202 MAC-7202
MAC-8202
8-ohm Dual (per ch) 300W 400W 600W 800W 1,200W
4-ohm Dual (per ch) 460W 650W 950W 1,300W 1,800W

Specification

Frequency Response ±0.1 dB from 20 Hz to 20 kHz at 1 watt
Phase Response ±10 degrees from 10 Hz to 20 kHz at 1 watt
THD 0.05%
Intermodulation Distortion
(IMD)
<0.35% (60 Hz and 7 kHz at 4:1, from full rated output to -30dB)
Signal-to-Noise Ratio >105 dB A-weighted or 100 dB unweighted below rated power, 20 Hz - 20 kHz.
CMRR (20 Hz to 1 kHz) > 55 dB, typically > 70 dB
Crosstalk (below rated
power, 20 Hz to 1 kHz)
> 80 dB
Slew Rate 80V/usec
Damping Factor >1,000 from 10 Hz to 400 Hz
Input Impedance (Nominal) 20KΩ Balanced
Signal Input Two balanced 3-pin female XLR connectors
Signal Output Parallel two balanced 3-pin male XLR connectors
Input Sensitivity gain 0.775 / 1 / 1.44 Volt
Output Circuitry Class H
Output Connector Two sets of Red & Black color coded binding posts & two Neutrik® Speakon® 4 pole chassis connector
Connectors Neutrik® 3-pin XLR, Neutrik® Speakon® 4 pole chassis connector
LED Indicator Power, Signal, Protect, Clip
Protection Protected against shorted, open or mismatched loads, overloaded power supplies, excessive temperature, chain destruction phenomena, input overload damage and high-frequency blowups. Also protect loudspeakers from input/output DC and turn-on/turn-off transients
Cooling System Internal heat sinks fitted with four variable speed fans for uniform heat dissipation from rear to front air flow
Construction Steel chassis with durable black powder coat finish
Power Supply Toroidal Transformer
Power Range 200 - 240V AC @ 50Hz
Model
MAC-2202
MAC-3202
MA-5202
MAC-7202
MAC-9200
Input Watts
(Power Consumption)
420W
660W
880W
1110W
1320W
Dimension (W x D x H)
482mm × 443.5mm × 88.8mm
482mm × 468mm×132mm
Size
2U
3U
Weight (Kg)
22.5
23.5
26
27
33

 

Description

The POPE Professional® introduces new Class D amplifier technology offering smooth and responsive handling with massive power output while maintaining POPE Professional's famous sonic integrity. The POPE Professional PM Series is using SMPS technology with built in 4 in 4 out DSP, the resulting high power, lightweight units designed for install sound applications.

The POPE Professional® PM Series is a range of 4 channels with 4 microphone, media player & Aux inputs. The PM Series can deliver 4 channels audio output and pre-out audio signal. The media player can play mp3 from USB, FM Radio & Bluetooth. The PM Series has been designed to provide that, Powerful Pure Sonic Performance which is now so synonymous with the POPE Professional® brand name. With the introduction of the PM Series POPE Professional® aim to deliver simple, pure and reliable power for applications where cost and ease of use are paramount without lose of integrity.

 

 

Features

•    Class - D Technology    
•    Power Factor Correction
•    Four-channel flexibility    
•    Phoenix input and output connectors
•    Self protection design    
•    Efficient cooling system
•    Comprehensive protection
•    4 in 4 out DSP
•    In/Out 10 Band Equalizer
•    20 Presets
•    PC Control via USB

Application

•    Shopping Malls
•    Places of worship    
•    Ballrooms
•    Coffee shops
•    Educational Institutions

 

Power Output

Ratings (RMS @ 1% THD @ 230VAC)

Model

Total
Channels

4Ω Per
Channels

8Ω Per
Channels


Bridged


Bridged

70/100V
(Bridged)

PM-300D 4 300W 300W  2*300W  2*300W 2*300W
PM-800D 4 800W 400W 2*1250W 2*800W 2*800W

 

Specifications

THD+N (typical) < 0.05 % (20 Hz - 20 kHz, 8 Ω load, 3 dB below rated power)
Signal To Noise-Ratio > 120 dB (A-weighted, 20 Hz - 20 kHz, 8 Ω load)
Frequency Response 20 Hz - 20 kHz ± 0.25 dB / 20 Hz - 20 kHz ± 0.15 dB
(8 Ω load, 1 dB below rated power)
Output Circuitry Class D - full bandwidth PWM modulator with ultra low distortion
Input impedance 15 kΩ balanced
Damping Factor > 2000 (8 Ω load, 1 kHz and below)
Media USB / FM / Bluetooth
DSP  
In / Out 4 In / 4 Out DSP
Frequency Response 20Hz to 20kHz
Gain -60dB to 5dB
Delay Input  5ms / Output 10ms
EQ Input  10EQ  / Output 10EQ
EQ Filters PEQ, LS6, LS12, HS6, Hs12
EQ Gain -24dB to 12dB
Q Value 0.267 to 92.302
Limit -19dB to 0dB
HPF & LPF 12 / 18 / 24 / 48dB LR / BT/ BE
Preset 20
Control Manual / PC
PC Connection USB
Level adjustment (per ch) Front-panel potentiometer
Connectors and Switches  
Input connectors Electronically balanced Phoenix connector for MIC 1 - 4 & RCA for AUX
Phantom Power On / OFF Switch for MIC 1
Output connectors CH 1 - 4 Phoenix connector & RCA for Pre-Out
Power on/off on front-panel switch
Cooling Fans, front-to-rear airflow
Front-panel indicators  
Per channel Power / Output signal / Limit / Protect
Bridge 1 & 2, 3 & 4 Channels
   
Safety  
Protection Circuits Input limiter, short circuit protection, DC protection of output, under & over voltage protection, SOA protection, intelligent mains fuse protection, power stage overload protection, temperature protection for transformer
Power
Type Universal & regulated switch mode power supply with Power Factor Correction
Operating voltage Universal Mains, 90-270V AC
Mains Power Cord
Dimensions (W x D x H) 482 mm x 410 mm x 88 mm
Size 2U
Net Weight 11 kg
Gross Weight 14 kg

 

PROTECTION SYSTEM

Clip Limiter: If the power amp is over driven and the limiter is set to on the clip detection triggers the Attack-Release-Circuit (ARC). The ARC delivers the control voltage for the gain reduction.
SOA Protection: Whenever the power transistors leave their Safe Operation Area (SOA), the SOA protection will either switch back the current rail of the respective channel or limit the maximum load current in the power transistors.
DC Protection: Each output of the power amp is constantly monitored for persistent DC voltage levels. If the 3 V thresholds are exceeded at any of the outputs, the corresponding channel will be muted. If DC was only applied for a short moment, the amplifier will release mute and work as normal. If DC is applied for longer periods or several short times the amplifier will switch to standby mode. Switch off the amplifier, wait until all indicator LEDs extinguish and switch the amplifier on again.
Over Current Protection: Over current is permanently controlled in the output stage. In case of excessive loading the maximum output current of the amplifiers is automatically limited. This improves reliability without degrading sound quality when driving complex loads. The main SMPS (Switched Mode Power Supply) transformer current of your MLSeries Amplifier is continuously monitored. If over current occurs the main SMPS immediately stops working. Should there be an internal failure this feature prevents other parts from being damaged.
Thermal Protection: There are sensors in each amplifier module in order to ascertain temperature data. If the temperature more than 85°C is detected at the heat sinks, the input signal on that channel is reduced proportionally to prevent further heating of the amplifier. If the temperature exceeds approximately 100 °C, the main SMPS is switched off (safety shut-off).
Mains Over Voltage Detection: Mains Over Voltage Detection is always operative. When the mains voltage exceeds approx. 268 V the amplifier will switch off. When the mains voltage returns to nominal value a soft start occurs.
Fuse Protection: The fuse protection circuit prevents amplifier shut-down (e.g. by a blown mains fuse or a triggered circuit breaker) during extremely hard use with all channels working at very high output power. Without intelligent mains current monitoring and control this could easily happen as the rated output power is several times higher than the capabilities of the standard mains supply. In order to prevent any shutdown in extreme situations the amplitude of the input signals will be reduced which will in return also reduce the mains current draw
Fans: The variable speed fans mounted in your ML Series Amplifier operate permanently, but as long as the temperature remains below 40°C, they run at their slowest speed and can hardly be heard. The highest detected temperature from any amplifier channel controls the speed of the fans. Above 40°C the speed is increased until it reaches its maximum value.

 

Description

The POPE Professional® MC Series amplifiers are  specially  designed  for touring and installation. It’s unique  design and  powerful  output  can meet the requirement of any sound reinforcement project.

Read More

About Us

POPE Professional Acoustics Ltd provides manufacturing, design and installation services to a wide range of POPE Professional sound equipment for Places for Worship, Auditorium, Seminar hall, Conference Hall, Discotheques and Live Sound. In the sound industry, POPE Professional is one of the leading brands in India. Our widest range of products provides to the different needs and taste of a myriad of Customer requirement for any application in the field of professional sound.

Recent News